Systems Errors
Error - "[4999] A parameter within the machine configuration file has generated a warning"
This is a pass-through error from the Renishaw UCC Server environment and is not a CMM-Manager error. This error indicates that there was a problem reading one of the parameters in the machine.ini file. This can be caused by several things. Locate ...
Reconnect Helmel PMAC controller after Windows Update
Helmel DCC / PMAC controller Error: PMAC Error 999 - General PMAC Error See attached document from Helmel for help reconnecting PMAC controller after Windows Update.
Error - "System Error: 106 Couldn't start grab"
This issue was discovered while setting up a Nikon Vision (Nexiv) system. All drivers and other setup items seemed to be ok, but when attempting to start vision, the error message was displayed. The AmCap utility would run. This led to the suspicion ...
Error: "Failed to open Pmac device 1"
Try running CMM-Manager as Administrator by right-clicking on the desktop shortcut and selecting "Run as Administrator". This error may show up on a Helmel CMM running a PMAC controller after a windows update. It may be necessary to restore the ...
Error getting Machine Data from I++ Server/Timeout
It has been observed that the CMM-Manager connection with the I++ Server times out and fails to connect in some cases. One possible reason for this timeout could be due to a large number of tips in UCCServer. Solution: Several workarounds exist for ...
Error - "error code 10054: WSAECONNRESET: Connection reset by peer"
This error may occur on an LK (Metris/Nikon) controller when settings on the PC are allowing USB and/or Ethernet to go into power saving mode. Please see information on disabling sleep mode for these devices at: ...
Error: "Error code 0x8002801d1 Library not registered"
The following message may be displayed when installing a DEVA control system or upgrading the DEVA driver: This may be caused by incorrectly installed DEVA drivers, installing the DEVA drivers without correct permissions, or use of devacmmctrl49. ...
Error: "Error code 0xfff9 Initialise failed. Interrupts not detected"
When installing or upgrading a DEVA interface for a CMM, the following message may be displayed: This likely indicates an improperly installed DEVA card (if PCI card), or missing/incorrectly installed drivers for the DEVA device, or the correct ...
Error - "System Error 84093 - Command Parsing Error"
Certain Brown & Sharpe controllers may display this message during initialization. If you receive this error during startup, please add the following line the the Sharpe32Driver.ini file. Path: c:\ProgramData\QxSoft\CMM-Manager ...
Error: Hardware accelerated driver / Missing, outdated graphics drivers
CMM-Manager requires a minimum level of graphics support to provide an optimized experience for full speed and rendering ability. This message is an informational warning only. If the appropriate graphics card or drivers are not available, ...
Error - "Failed to open (PHC) Com Port"
Verify that the proper COM port drivers are installed and active by checking Windows Device Manager. Verify that CMM-Manager is attempting to open the correct COM port. Make sure that a Windows update has not changed COM settings, or more ...
UCCAssist-2 error: Security files have been changed without permission
For issues relating to the error message seen below: This is a known bug and the error message can be resolved by deleting the DefaultMachine.ini file.
Error - 23918: Lost communication with CMM Controller. UCCServer is not running.
If error 23918 "Lost communication" is displayed and the machine has sat idle for a time, please make sure that Windows and the Network / USB ports are not going to sleep. If they do, the internal communication connection (Windows socket) is lost and ...
Error - "[4999] Unable to establish a connection to the controller", "Controller communications failure"
This is not a CMM-Manager error message. It is a pass-through error message that comes from UCC Server and is displayed by CMM-Manager for the user. This message indicates that Renishaw UCC Server or the Renishaw UCC Driver cannot communicate to the ...
Error - "No such node (XMLTree.Part.Geometry)"
When attempting to sync CMM-Manager with UCC Server via XPath, the error message "No such node (XMLTree.Part.Geometry)" is displayed. There was a bug in UCC Server regarding XPath and the UserPartsCatalog.mxc file. When a sync occurred, the ...
Mitutoyo - Mitutoyo CMMC and ComUC Error Code Table
Here is a table of Error Codes for MTI CMMC and ComUC DCC controllers.
LoadLibrary failed with error 87: The parameter is incorrect
CMM-Manager failed to launch with the following error: This error occurs often when CMM-Manager is launched remotely over RDP. While most users may never encounter this issue, it is common for IT personnel to maintain the PC remotely. Sometimes, this ...