Temperature Comp
There is a temperature compensation option that can be used, how do you use this feature exactly? Also is there a way to have the temperature at time of the program running to be added to the report?
CAD Shift After Alignment
Hello, i am running into an issue that i am hoping to get some help with. I have been running a program fine for a while and then all of a sudden i have been getting a lot of collision into my part. I believe the problem i am having is after my alignment
Cylindrical probe calibration
Where can I go to change the qualification angle to calibrate a cylindrical probe? I want to come up off the equator of my calibration sphere by 5-10 degrees. This is to ensure I'm calibrating the radial end and not hitting the cylinder part of my stylus.
Is there a way to set a directional bias for checking feature?
I have a part that is essentially a "T". where the leg meets the cap there is a radius that runs parallel to the cap. This radius can be measured from either the X+ or the X- side of the part. When I use "fixed quill" it measures the feature from the
user Manual
I know that I may be old school, but YouTube videos do not work well as instructions for me. My desk and computer are quite a distance from my CMM's, and walking back and forth, starting and stopping, and rewinding the videos is not the easiest thing
Move CAD/Program
What's the best way to move the CAD and related features/measurements, after the program is written? My current issue is, I recently noticed my CMM table location was set too low. After updating the table location, some of my cad models are "buried" in
Saving / Sharing / Accessing Programs on another CMM
So we currently have 2 CMM's which are about 100 feet apart from each other. With Tech Supports help we were able to make a program on our manual CMM. I would no like to transfer that program to the other CMM, and store another copy on our server for
Shop Floor Mode
What size image does Shop Floor mode show? I want to add an image for the icon for visual reference, however it currently crops 98% of my full image out due to not resizing and just using set pixels. i will resize my image to fit once I know what pixel
Finding the apex of a cone
My print calls out the Position of the apex of a cone (a divot/concave shape) and I'm having a hard time getting a theoretical point on the apex. Measuring as a cone feature works fine except when I evaluate the position, it assumes it's from the base/largest
Custom Probes using Renishaw UCC server
I bought some 18MM disk probes from ITP and discovered that since they were not in the Renishaw catalog nor match anything within the Renishaw probe offerings that I could not build them in UCC server (have been using CMM manager for 5 years but this
Probe not reading correctly
I need some help. When we go to calibrate our TIP, it doesn't read correctly. So I will put on a tip 2.50 change it to 2.50. When we go to calibrate , it'll read 6.798 every time. Do anybody have a clue why this is?
Reseller
Nate As a reseller what do we do going forward for licensing, contacting, and ordering?
Most Discussed Topics
Newbie Program Order/Alignment Question
Hey there, I've beating my head against the CMM table for about a month now and am giving in and asking for help. Firstly, thank you so much to everyone who contributes to this community. I have learned so much in the past few months from this site alone.
2 clouds bestfit to plane
I have 2 planes that I need to know how they are to one another. Is it best to choose each one as a cloud, then combine them using "Best fit" and see what the flatness is, or should I pick up each one as a plane and check how parallel they are toget
Change depth for all selected features
Hello, I was just wondering if there was a way to change the depth on all selected features at the same time? I've got a part that has 200+ holes and I've got the depth a little too deep. I was hoping that I could change the depth for everything similar
GD&T Question
Hi All, I have a print that calls out .0004 true position on two open slots. It does not give a Datum at all. Is this a mistake? or does it mean true position to each other. Thanks in advance.
Fixture recall alignment
I'm probably overthinking this, but I'm hoping for some input on if I'm on the right track or if there's a better way. I do almost all of my programming offline these days, we probably have hundreds of programs. I want to get to the point where I can