Profile vs Cloud to CAD
I want to check Profile of a surface. What is the best way to calculate it, Report Profile or Cloud to CAD? Does Cloud to CAD report just the worst point deviation or does it report the actual profile (2x the worst deviation)? I need to submit data to
Multiple hole collection via remote trigger on Faro arm
I have a part with 2 lines of holes down 2 rails, approximately 40 holes. The holes are identical and the spacing is identical as well. Is there a way I can trigger another "element" to collect via the red button on the Faro arm so I do not have to return
"Plunge" speed
Is there a way to change the speed only when plunging into a hole? I get nervous when measuring small holes with small tips, so I'll slow down the DCC speed, but it affects the entire move to the hole too, which can be excruciatingly slow. I would like
Generating Measurement Locations on a Surface with a Complex Boundary
Is there a way to generate touch probe measurement locations on a surface with a complex boundary? For example, let's discuss the surface below. Because it is a narrow surface, I switch from the "Target Point #" method to the "Along Edge" method. If I
Bilateral Position
Can someone tell me how bilateral position (in on direction) is calculated? I need to explain it to someone. I know how to calculate regular true position. Thanks.
Q-Das export
Hi, Is there any plans in the future to add support for the Q-Das format like the already existing QC-Calc report file format? And if so, what is the timeline for this? Thanks,
GD&T Font?
I've noticed since we updated our software, it shows symbols for GD&T in the report. These symbols show up on the PC that CMM Manager is installed on, but not our other PC's. Is there a font I need to install to see these GD&T symbols?
Does CMM-Manager know how PH10-M Head turns?
Hi, question is basically in title, does CMM-Manager know how the head turns from one angle to another? Especially the turning angles (clockwise, counterclockwise).. In the simulation it only jumps to the new tip angle.. Best Regards
More Complete Measurement Generation for CAD Teach 2D (Vision)
I've noticed that when measuring 2D vision CAD features and automatically generating measurements, only 4 measurements are generated (at least for a circle). Is there a way to automatically teach measurement locations that measure the circle's complete
Using CAD alignment for your initial alignment instead of 3-2-1
I have about a years worth of experience running/programming with CMM manager so I was just hoping to get some opinions to give me peace of mind. When it comes to creating alignments I was wondering if would be alright to use the CAD alignment instead
Does UCC Server allow probe assembly setup not in renishaw list?
Question in title. Boss wants to buy probe styli from QMark. Thanks! :)
Struggling to measure a specific chamfer with CMM Manager – advice needed
Hi everyone, First of all, I apologize if this question has already been answered before — unfortunately, I haven’t been able to find the information I need. Probably this is something very simple, but it’s been giving me some trouble. I would like to
OFFLINE PROGRAMMING ALIGNMENT ISSUE
I have a question / problem with a part I'm programming offline. I initially saved the cad file in position from the cad software so when I import the file it comes in on the three-jaw furniture I created. So I don't have to move the part once in the
Newbie Program Order/Alignment Question
Hey there, I've beating my head against the CMM table for about a month now and am giving in and asking for help. Firstly, thank you so much to everyone who contributes to this community. I have learned so much in the past few months from this site alone.
Change depth for all selected features
Hello, I was just wondering if there was a way to change the depth on all selected features at the same time? I've got a part that has 200+ holes and I've got the depth a little too deep. I was hoping that I could change the depth for everything similar
Mitutoyo BH and Bright Communication
Hello all, I have one of each of manual Mitutoyo BH and Bright CMM units. I have the Renishaw probes and calibration balls. What I lack is whatever PCI or USB interface I need to communicate with the CMM machines. I have the GPIB board on the CMM side
LK CMM NMC 300 Controller Probe Disarm
Machine: LK CMM with NMC 300 controller We have noticed that on execution of a "Get Probe" command the first thing that happens is that the probe disarms and CMM Mgr seems to take the shortest path to the safe position at the rack disregarding anything
B Rotations - Avoiding 315 turns?
Many many years ago, I remember hearing/reading something about CMMM trying to avoid excessive rotations for B tip changes. Example: If you're at A90B0 and want to go to A90B-45, having the head turn 45 degrees during the change instead of 315 degrees.
Using a hole pattern for secondary and tertiary datums?
I had a discussion this morning with customer about a part where they had a plane as Datum A and a pattern of clearance holes as Datum B and considered that as a complete reference frame. After the call, I did a little research and apparently this is
DDE File Creation on New Job
I'm still very new to this DDE reporting. I just figured out how to make it work and put results where I want them. Is there a way to have it create a new Excel file for each new job? Right now I've been saving all the standard reports to a folder, appending
Joystick Unresponsive After Automatic Operation on LK CMM – How to Reduce Delay?
Hello, I have an LK CMM with a hand controller like the one in the picture. I've noticed that after the machine completes an automatic operation, the joystick becomes "disabled" for a period of time before I can use it again. I have timed this delay,
Bolt hole pattern as a primary datum
Is there an optimal way to use a bolt hole pattern as a primary datum that constrains the proper 5 degrees of freedom it's allowed? I have 8 holes spaced evenly at 45° at typical compass directions, all are nominally angled in the Z-Axis. If I measure
Plane-Line-Circle Alignment Issue: Features Not Showing in Features List
I need help with something that should be simple—I’ve done it before but can’t remember how, and I need it urgently. When aligning my part using Plane-Line-Circle in this specific case, I can't get these three features showing up in my feature list for
Finding a theoretical HeadSpace on a 7.62 round
I will do my best to explain what I need done, but so far I can not figure a way to accurately get this to measure. I have attached a picture as well. The idea is I need to measure from the bottom of the headcase (bullet) to the mid shoulder of the bullet
GD&T symbols on reports
Does anybody know how to switch from the GD&T name to the symbol on reports? Saw it in the software update notes and thought I would give it a try. I've been looking for the option in the settings but cant find it. Thanks, Ed
Tip Manager - Add more Columns
Is there a way to add more Columns? E.g. last calibration date..
Square up part program
Somewhat related to an earlier post: https://support.qxcmm.com/portal/en/community/topic/move-cad-program Is there an easy way of "squaring up" a part program? For example, I primarily write my programs offline, so the part is perfectly square the machine/program.
Star Probe
Hello Everyone, I am using CMM Manager with my Mitutoyo Crysta-Apex S, and was wondering if anyone here has set up a Star Probe within the CMM Manager? I could use some tips. I have never create a star tip. Can you any help to get started.
Sync CAD & Programmed Elements
Hey guys, I messed up a program and ended up with my Elements (Circles, Planes, Lines...) not laying at the right position on the CAD Model.. Is there a way to sync these elements with CAD Model again? E.G. creating a coordinate system for both and sync
REPORTING STRAIGHTNESS WITH BONUS TOLERANCE
Hello all, I have attached some photos that show what I'm trying to report. I have been asked if my current report can take into account the bonus tolerance for the straightness under maximum material conditions. I have never run into this so I'm honestly
Plane-Plane-Plane Alignments?
I realize that CMM Manager wants to use just a line for an alignment and a point for an origin, but this isn't true GD&T. Is there a way to use planes or other full dimensional features for alignment and origins?
finding the apex of a cone on a small surface
Hi All, I have a 11.5 inch base diameter cone, 60 degree angle. The angle is appoxamently 1 inch thick. I need to find the apex of the cone. This is my datum A. CMM manager is giving me a number that is about .015 to large, would this be accurate or is
Switch Reference Frame only for Reporting
I'm programming a qubic part with holes in all sides and different origins on the drawing.. I'm not sure about the strategy but I have an idea and would like to hear your opinion before I start.. I would align the part and sync CAD.. Then I would measure
Change the order of the report columns.
Hello gurus of cmm manager, So basically i have two different cmm machines and when they go to print the reports the report header columns are in a different order. Machine A: Nom, Act, Dev, LoTol, UpTol, OutTol. Machine B: Act, Nom, LoTol, UpTol, Dev,
adding probe rack
Hello all, We're looking to add a probe rack to our cmm and I don't see any information that will tell me if this affects programs already in use? Will older programs that call for tip changes just automatically change once the system is taught that there
Vision only alignment?
Hi, I am currently playing with the trial software to assess whether we want to go ahead with purchasing. I am interested in using ONLY vision tools for this assessment. I cannot for the life of me figure out how to do a basic alignment. Any software
Cad Alignments
Hello, how do I add 2 cad alignments and save them so I can recall them in my program? Sorry if this has been answered already, but I can't find it. Thanks
Cloud to CAD Profile evaluation without Point Data Output
Hey guys, is this possible? I want only the head data and not all the point data.. Thank you!
Report On Slot Length Between Circle Centres
I have the attached drawing I have to report on. I have measured the slot as a 2D CAD Slot, but when I report on it I can only report on the overall length and width. If I try to construct a line along the axis it makes it full length not centre to centre.
Report Properties Inspector Name
I cannot get the 'Inspector' field on the Report Properties to retain the change I make to it. If I go to the Report tab in Teach On I see one name, when I run the report in Teach Off I see a different name, and no matter which I change and then save
Next Page