Fixture recall alignment
I'm probably overthinking this, but I'm hoping for some input on if I'm on the right track or if there's a better way. I do almost all of my programming offline these days, we probably have hundreds of programs. I want to get to the point where I can
Unilateral Profile of a Surface
I'm working on an inspection that calls out a Unilateral Surface Profile of an ID cylindrical surface. There is a zero following the U in the profile callout, indicating that the drawing/model is at MMC, and the Radius can be bigger than the Basic, but
How to measure a diamond-shaped locator pin?
This might be a basic question, but I’m struggling with it. How would you approach measuring a 2-way locator "diamond-shaped" pin, like the one in the image? I need to report (GD&T) the position of that pin as well as the longer size (length) , so I assume
Larger Icons on custom toolbar
I have searched the KB and found nothing on this, but how do i get the custom toolbar icons much larger than they are now.
Alignment of a "long cylinder"
Hi all, As per the nature of my question, you can infer I am just a beginner so, thank you for taking the time to help me as, unfortunately, I couldn't find any related topic here in the community area. How can align a part, locking all the 6 DOF, that
Aligning to a pattern
What is the ideal way to align to a pattern of holes? What I had been doing for the attached part, was setting my origin to Datum A, then aligning to one the holes for Datum B. After some discussion with Engineering, they said the pattern itself was the
USING IGES FILE FOR PROGRAMMING
Receiving Inspection reports up through me at the company where I work. My boss suggested recently that 4-hours was too long to program. Their previous roles, allegedly the programmer could import the IGES file, align the machine and be ready to run in
Position of a feature on a plane perpendicular to the leveling plane
Hello to all, I am measuring the position of a feature R13, that is perpendicular to the reference frame A/D. This is not usual on the part prints I work with. A .ppt was attached showing what was done, but I would like to hear some comments or corrections.
Best practice for reporting diameters
I hope I can explain this adequately. To the best of my knowledge, according to ASME standards, when measuring a diameter, every point on that diameter needs to fall within the drawings stated tolerance. If you have a diameter that is out of round, some
Properly applying projected tolerance
I accidentally submitted this as a "Ticket" yesterday, but thought it might be good community knowledge. Original question: I found the article https://support.qxcmm.com/portal/en/kb/articles/gd-t-projected-tolerance-zone , however, I would still like
CMM MANAGER MEASUREMENT QUESTION
As you can see in the video, the plane measured as expected in "simulate" mode, yet it measured inside the math model when physically measuring the part. Thank you.
Does RefTip Calibration Status get lost when loading a Probe File?
Hi, can you confirm if Calibration Status of the RefTip gets lost, when I load a Probe File? Other Tips Calibration Data seems to stay like before after loading the Probe File.. Is Calibration Data of the RefTip is saved in the Probe File instead of the
Ask for Active Probe in Program
Hi, is it possible to let the user who runs a program verify the active Probe and if it is different from the one CMM-Manager thinks is active let him type in the correct one? Background is, we would need to run both Mitutoyo MCOSMOS and CMM-Manager for
Reference Tip Usage
New machine, new questions. In general practice, I've heard you don't want to use your reference tip for part measurements. Our new machine now has a rack for changing tips, but I currently only have two stylus holders (SH-25-2), so I am currently limited
MMC calculation on perpendicularity
My Datum B cylinder is measuring about .004" over MMC. Why am I seeing only a .001" bonus when reporting my perpendicularity? Am I missing something?
MITUTOYO MAG-3 DSW2 DIP SWITCH CONFIGURATION/ GPIB ADDRESS WIH NI GPIB PCIIA 488.2
MITUTOYO MAG-3 DSW2 DIP SWITCH CONFIGURATION/ GPIB ADDRESS WITH NI GPIB PCIIA 488.2 Removed DMA notification. Updated: 2022.10.17. 16:29 UTC+2 I attached in pdf format. Best regards
Moving Part to new Position... See these photos attached in this Topic
Hello CMM Community. I know this topic is covered, but I'm struggling to understand the written directions on how to execute what I need. I am attaching 3 photos of the same part but in different positions. How do I program this into 1 program. I want
RTP20 with Deva004
Is there any experience in RTP20 hitting Pole with the lever on the way to indexing to a new position? Ends in E-Stop
Advanced alignments / Cloud-to-CAD alignment
I'll preface this by saying that 95% of our parts are machined and have nice, orthogonal faces. The past few days I've been getting parts that have no flat surfaces. They are essentially a contoured ridgeline, that will become a fixture for an internal
Compensation Map
Hi everyone, this problem i'm having it's more service related, i have a manual CMM Mitutoyo with UD1 card and runing CMM Manager 2020, the thing here it's that in the X axis i'm having a deviation of 24 microns in a 400 mm gage, but i can't compensate
Manual programming hits doesn't register automatically
Earlier manual hits taken, used to get register automatically but suddenly not sure why it asks to press Spacebar key to register manual hits. Is it configuration change ?