CAD Import settings
How do I access them?
Axis Inner Limit Switch
Hello, we are having an issue with the Z Limit Switch on our CMM machine. We crashed the stylus into the part and it knocked the stylus off. It was not a hard crash, the stylus was inside of a bore about an 1/8" from the surface and the probe went the
Single Reports - Multiple Parts in Loop
I have created a loop (not batch run) that is running 10 individual parts. The results are calculated inside the loop. My results are created in one report. Is there a way to create multiple reports, individual for each part?
Probe calibration question
My tip calibration Deviation is high, around .0015", is this normal or should this be lower. Also, I have checked the diameter of several ring gages and they are always off around .0006". Any feedback or recommendations is appreciated. Thanks
Keep Layout when switching Language
Hi, seems Layout is tied to the Language.. Would it make sense to decouple Layout and Language? Thanks for considering!
Concentricity
OD Circle 1 BC Circle 11 When comparing the 2 features and even changing the origins why do the XA and YA values stay the same? For instance I want to know which way to move my BC diameter so it's concentric to my OD. With OD Circle 1 set as the origin
how to move an end point
how do I move a start and end point? if i dont like where it is because its to close to my part.
Visit QxSoft at the Quality Show South in Nashville
QxSoft at The Quality Show South 2024
Graphical Report without CAD
Is there a way to generate a graphical report for a simple line without CAD? I want it to look something like this, only a straight line. The problem I have is that this seems to be ONLY generated by clicking on the "Report Cloud to Curve" button, which
4-Way Stylus Centre Probe Building
Attempting to build a probe utilizing a 4-way stylus centre (3 30 mm long styli at 120 degrees apart along x & y, z- will not get a stylus). Can I treat this as a disk probe when building, or is there a proper procedure for this style of centre? Any advice
RTP20 pole issues
I run a program with the RTP20 probe at a 90 degree angle. In the program it changes to another angle using the "Get tip" feature. I ran the program 4 times without a problem, when I tried a 5th time the probe release arm misses the pole completely, subsequently
CMM Manager with Manual Machine
We recently just got a retro-fitted TESA micro-hite 3D. Does anyone have any experience with this modification and can point us in the right direction on how to use it? Or have any helpful pointers? Thanks
POSITION BASICS AUTO POPULATE
When entering true position basics in the main windows, what if it were to auto update the basics located in the feature report tab after you enter your actual basics after you hit apply? Thoughts????
Combining multiple reports for PPAP submission to AIAG form
What are options for combining multiple parts into an AIAG PPAP submission? We currently have a "homegrown" software that has us manually enter the data line by line. Does anyone have excel examples or something similar that would be able to combine,
new to cmm...basic help
I will go ahead and apologize in advance. I am brand new to EVERYTHING CMM. I took the 3 day basic training but it was just to much information for someome who has never seen a CMM. Apart from turning on the machine and homing it, I know nothing. i just
Linking between holes
We have many parts with over 100 holes and for some reason linking between them does not always happen correctly. We are fairly new to CMM manager but can't seem to figure out why this happens. Another issue that also came up was the path wanting to stay
Radius in Z
Newish to CMM programming, we have ph20 head and CMM manager 2022 software. So there will be times where I have a radius that needs to be checked. For some reason I struggle to find good ways of checking the part. Like if the radius goes around a lathe
Updated PTB Certificate
We've obtained an updated PTB certification. You will find the legacy CMM-Manager PTB certificate along with the new 2023 certificate here - NIST Algorithm Test / PTB Certificate (qxcmm.com) More info about PTB here - Physikalisch-Technische Bundesanstalt
cmm manager program file size
is there a limit for program sizes? i made a program that was about 135,000 KB and cmm manager operates extremely slow. the problem doesnt seem to be stemming from my PC since i'm using less than half my CPU/MEMORY. anyone ever experience anything like
True Position of XY&Z
I've got a series of holes with carbide balls inserted in them. I need to measure the hole diameter, then take a hit on the apex of the ball to report position. The holes vary in location from nominal. How can I ensure I'm taking a hit on the highest
Possible to have multiple TCR20 racks?
Hello, As the title says, I was curious if it was possible to have multiple TCR20 racks so that we could have up to 12 probes available for usage without having to replace the current 6 that we have. Thank you, Kaleb
HOT !!! Using imported cad planes for projection of measured features
Got a hot project I am starting in the morning If I pre-create several plane CAD features that I want to project measured lines and arcs to. How do I use these CAD planes to do that in CMM-Manager?
Free - LK Micro4 Horiz Arm CMM
UPDATE - Sold... to the lowest bidder... LOL. We salvaged what we could and sent this giant 14,000 lbs. hunk of granite to the local stone quarry. Anyone interested in a rather large CMM? We're moving to a new facility and would like to not bring this
Section Views
Having trouble creating a profile of a line. Only video I could locate. I can create the graph, but the tolerance band does not show up. Does anyone know of a video showing how section views are created? https://youtu.be/v1RuDBT-EAc
Editing group of identical CAD measured features at once?
Is it possible to edit a group of CAD measured features at once. For example say I have 100 identical cone measures I have programed but realize it may measure better with the boundaries spread between the two levels it takes points at. Usually something
UCC Server/TCR Rack
This is not really a CMM Manager question but I am going to throw it out there anway. Ph20MT with TCR rack. When picking up the sensors, sometime it will stall out on the exit. It looks like it is not really picking anything up, but just trying to move
Editing features
Is there any way to edit this after the fact? I have a program that was entirely created in manual mode, unintentionally.
Shortcuts
Is there a way to get a report of all the keyboard shortcuts? Ive looked in the help files but the newer version doesn't match what is shown here.
Wanted: CMM-Manager 2022 Beta Testers
CMM-Manager 2022 Beta Releases on Friday at noon (Eastern US Time Zone) - Want to participate? Register Here:
Renishaw TP20 Racks MCR20 vs TCR20
MCR20 vs TCR20 Stylus Change Racks both work in CMM-Manager and as you can see the TCR20 is significantly less expensive than the MCR20. The TCR20 is not currently listed in the CMM-Manager software because it is actually intended for PH20 probe heads
Fixture gages and batch run
I have a fixture with 10 nested parts. I setup the run by doing the coordinate on the first part then y axis offset. Asking the group before I send a helpdesk but…. How are you making sure the gage is running true to the machine. My thoughts are to use
Using Multiple Probes on a Manual CMM
Hello, We are running CMM Manager Manual LT version 3.3.2.2014 (2013-0829) We have a manual Mitutoyo BH706 CMM with a Renishaw MIP head, and few different styli combinations. Most of the parts we run typically only need one size stylus, but a particular
UCC Server Guardian
Does anyone know how to enable Messaging Service in UCC Server? This is the message I get when opening Guardian.
Filters with Scanning in 2D/3D
Is it correct that it is not possible to have filters activated when scanning eg a cylinder? For circles it's okay and for planes it's possible too...
Saving as an older version
Is it possible for me to write a program in CMM Manager 2022 and save it as an older version like 2021?
5-axis commands inc. angle
haven't been able to find a good write up on this so i was wondering what the CMM manager community's thoughts are. is there a best practice for selecting the angle? i typically select it based on clearance but may be sacrificing accuracy? preferences
Option to add note to a selected amount of features?
I wasn't sure if this was in the software somewhere and I'm just missing it but it would be nice to have an option to add a note to a selected amount of features. For instance, I have a part that I'm measuring 500 holes and I need to add the GD&T in the
CMM Loosing Position
I programmed the CMM to measure the top of a 123 block at a specific place. This place has screws which locate the block and prevent it from moving. After running other programs, the CMM seems to loose its programmed position to check the 123 block and
composite profile
what method are people using to report composite profile tolerances? example profile to ABC and a composite profile back to A. Is there a function within CMM manager that reports this similar to composite positions?
How to control Approach vectors?
I have a part with a cylinder coming out from the side. CMM Manager keeps trying to approach from the side where the main body interferes. How to I force it to come at it from the open end of the cylinder? Is there a "Toggle Bias direction" somewhere?
Next Page